Mooks HQ, HJ, HX, HZ, WB Sandman Mockup

**RodneyHZ253** · 20-08-2011, 04:17 PM

Mook I glued felt underlay about 12mm thick with laminex or vinyl glue to wall and ceiling prior to installing any linings from memory I had to cut a groove in it for the ceiling bows for hood lining .the bows had less than 12mm clearance from roof

**mook** · 21-08-2011, 01:35 PM

That sounds like a great way to do it, in your opinion do you think that it makes much of a difference to the outside noises getting in?

I just purchased enough Dynamat to do the roof and the front floor under the carpet. Spent a small fortune, but i figure do it once and do it right.

With the lining rod did you have a wide gap in the felt for the bow? Was this so that the bow fitted easily when clipped in, or did you do this for the roof lining to clear the felt?

**RodneyHZ253** · 21-08-2011, 03:26 PM

I groved the felt out so that the bow did not contact it and left clearance each side of the bow so when the lining was pulled tight the bow could move with reference to the lining I didn't end up using the thin wire and clip it to roof brace i couldn't get lining taught so I made up an extra bow out of mild steel rod to match the two rear bows I had.

**mook** · 21-08-2011, 03:56 PM

Originally Posted by RodneyHZ253

I groved the felt out so that the bow did not contact it and left clearance each side of the bow so when the lining was pulled tight the bow could move with reference to the lining I didn't end up using the thin wire and clip it to roof brace i couldn't get lining taught so I made up an extra bow out of mild steel rod to match the two rear bows I had.

Thankyou, very helpful.
I don't have the little lugs where the wire would go on my van (maybe a WB thing) so I think that this will work well for me.
I'm sure i can find another roof lining bow from another car that i can quickly modify.

The new bow I'm assuming was put in place just behind the bulkhead but leaving room to move when tensioning. (maybe 1cm back)

**HZ EVIE** · 21-08-2011, 04:29 PM

Sounds like it's going well Mook, can't wait to see the finished product (I bet you can't either!!).
On the note of head lining bow's I know we used to be able to buy reproduced bow's, but can we still, should I look at getting some second handies, or should I try and get some made up. Hoping in the next couple of months to have mine to the headling stage, so I had better get my but in gear!

**mook** · 22-08-2011, 11:43 AM

Originally Posted by HZ EVIE

Sounds like it's going well Mook, can't wait to see the finished product (I bet you can't either!!).
On the note of head lining bow's I know we used to be able to buy reproduced bow's, but can we still, should I look at getting some second handies, or should I try and get some made up. Hoping in the next couple of months to have mine to the headling stage, so I had better get my but in gear!

Drop Oz a line, he may be able to help you with the roof lining bows.

I have re-listed my fancy dash facia
http://www.ebay.com.au/itm/130565444...84.m1555.l2649
I can post better pics if anyone is interested.

**HZ EVIE** · 24-08-2011, 08:45 AM

Thanks for the help Mook. Keep up the good work!!

**Dago** · 24-08-2011, 09:50 AM

Originally Posted by mook

I'm quite sure that a chrome bar will still cut through a softer modern car. Not to mention Kangaroo. :Chin:

I hit a roo without my 5 poster. Smashed out my grille and bent the chrome bar. I'm with WB

**Blocker** · 15-09-2011, 09:10 PM

mook - these are my 5220's they just need a scrub or blast and a coat of Pacemaker blue.

**Jez_505** · 19-09-2011, 11:53 PM

Looking good mook.

just have to say its scarely similar to the 83 wb im scratching together. Jamaica lime?

ill upload photos as soon as its out of the panelbeaters

Keep up the great building