Page 4 of 8 FirstFirst ... 23456 ... LastLast
Results 31 to 40 of 74

Thread: Aftermarket A/C

  1. #31
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,092
    Thats the go brand new unit cant go wrong look forward to the install and thanks for taking the time to post pics
    cheers G.

  2. #32
    Bits have started to arrive

    First was the "adaptor kit" to mount the Sanden compressor
    (If you recall last post, I determined the factory mounting plate had mounting holes incorrectly spaced for a Sanden)
    You still need the factory Cast piece for A/C & Alternator mounting
    IMG_7324.jpgInstructions
    IMG_7326.jpgKit Contents
    IMG_7327.jpgComparison to factory mount - note the adaptor only picks up on two lugs, not three as per original.

    IMG_7328.jpgCompressor (in box)
    IMG_7336.jpgCompressor out of box - advice is the 7 chamber pump is better than the 5...time will tell

    IMG_7338.jpgCondenser - need to fabricate up a mount.

    IMG_7329.jpgControl unit
    IMG_8039.jpgLooks like this when fitted

    IMG_7330.jpgDrier(?)

    IMG_7331.jpgBulkhead fittings (one for A/C, one for Water - can get in a line of 4 or square of 4 - I chose this way)

    IMG_7332.jpgBlanking plate - even pre drilled - pleasant surprise!
    Last edited by Puzzigully; 25-07-2018 at 02:01 PM.

  3. #33
    Didn't take a pic of the Unit - but it's going to be a challenge to fit it in!
    The outlets on the top for demist foul the curved section when you push it back against the firewall.

    Might take a few beers and think time to locate the best place.

  4. #34
    Sandman Driver maxsandman's Avatar
    Join Date
    Aug 2014
    Location
    country N.S.W.
    Posts
    621
    Looks like Christmas!

    Sorry, I don't recall what vehicle this is going into??

  5. #35
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,092
    That looks like a good kit hope it all goes in smoothly

  6. #36
    This is going in a WB Panel Van with HZ GTS dash, seats and front - Sandman replica

    Sent some of the older parts off to be powder coated so they look pretty

  7. #37
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    Did all this come as a kit ? Who was it purchased through ?

  8. #38
    Quote Originally Posted by jason.ruff View Post
    Did all this come as a kit ? Who was it purchased through ?
    No, but you can purchase as a "kit", but you still dont get everything illustrated.
    I also need to get demister vents yet as well.

    There's many distributors of Vintage Air in Australia, but only one who i know does the blanking plate.
    Retrospares in Eltham Victoria sell the Vintage Air and blanking plate
    https://www.retrospares.com.au

    - - - Updated - - -
    It's being installed in this:
    Attachment 16693
    Last edited by Puzzigully; 26-07-2018 at 02:05 PM.

  9. #39
    Sandman Driver damienengland's Avatar
    Join Date
    Oct 2012
    Location
    Chelsea, Victoria
    Posts
    772
    Hey Puzzigully

    Notice that you seem to have the bracket kit that i got. If its the same one, make sure you cast a critical eye over the Sanden pulley alignment with the engine pulley. My Sanden was just a fraction too far back and you could notice it with the belt installed, so i used a couple of the supplied washers to push the Sanden forward a smidgen and that lined up the belt really well.

    Cheers

  10. #40
    Hi,

    Thanks for the tip - I'll pay very close attention to the alignment!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •