Hey Valencia...yep i would generally agree and pondered this myself. I can still leave it out, but i did decide to put it in as i figured the paint shop could work around it...and i'm keen to see progress anywhere...I will have another think...
Hey Valencia...yep i would generally agree and pondered this myself. I can still leave it out, but i did decide to put it in as i figured the paint shop could work around it...and i'm keen to see progress anywhere...I will have another think...
Installing the windscreen.
Window goo gets applied...
PXL_20230318_205938816.jpg
Window gets plonked into place...
PXL_20230318_211331981.jpg
Electrical stage 1. This was basically taking the old WB Statesman Caprice loom, threading it into the van and then connecting new modified looms for hidden engine bay wiring, hidden battery feeds and additional circuits. This was crazy painful and took weeks of effort. The reward was turning on the lights, and testing the horn and indicators for the first time.
Get the old loom into the dashboard...
PXL_20230312_023252284.MP.jpg
It was heavy going around the fuse panel and drivers side A pillar. This is where most things intersected from the rear and front of the van...
PXL_20230312_054835928.jpg
A lot of the new circuits were sent to the centre console area as they will either be controlled from console switches or the Haltech ECU which got mounted inside the console...
PXL_20230325_063934626.jpg
I also got the twin batteries mounted up under the van body. They are bolted to a custom steel plate which was laser cut to fit onto the chassis...
PXL_20230304_023814526.MP.jpg
This was a good night. Basically all of the body harness was in and connected to the batteries so i got to test the lights, horns and other stuff...
PXL_20230402_042032190.jpg
After weeks and weeks...and weeks of wiring work, it was time to drag it out of the garage and send it to a shop. Basically I can't do the things needed next, i just don't have the right equipment, hoist or skills. It was a good day to clear the van out of the garage...
To make the van mobile, i needed to get some front panels and the boot back from the paint shop and fit them up. This was good because i got to see (or not see) my hidden wiring looms in the engine bay...
PXL_20230422_083342006.jpg
Big moment, drag the van out of the garage...
PXL_20230424_000814820.jpg
Dropped it off to its new home and then went and lay down for a while to recover from all the work...
PXL_20230424_012513879.jpg
Last edited by damienengland; 30-07-2023 at 10:59 AM.
So now the van is in its new phase, which is having the pros do their bits to get it going. So far they have installed a stainless exhaust system, air intake system and fuel fill pipe (from the rear taillight down). Here's some pics...
Exhaust system.
Twin 3 inch with cats (engineer made me do it) and twin O2 sensors, then twin 2.5 inch from the rear muffler going back to exit points just behind each rear tyre...
PXL_20230729_040131566.MP.jpg
PXL_20230729_040214019.jpg
Air induction system
4 inch stainless steel pipe and air box lid with a standard Commodore box underneath...
PXL_20230729_040613094.jpg
PXL_20230729_040623424.jpg
PXL_20230729_040636059.jpg
Fuel fill pipe
Running from behind the taillight and through the void panel area to the tank...
PXL_20230729_032728021.jpg
PXL_20230729_032743451.jpg
PXL_20230729_032835029.jpg
Last edited by damienengland; 30-07-2023 at 11:03 AM.
There are currently 5 users browsing this thread. (0 members and 5 guests)
Bookmarks